Didn't know there was one. This can be done in one of two ways. The hard drive that has a bootable partition must be made to be first in the list, Save bios settings.- or - you must change which data header the drive that Cutter Says: September 20th, 2010 at 6:28 pm Paul, Thanks for your information… I'm reminded of the Dilbert strip where the boss says, "I want to browse the Internet. his comment is here
Paul, you offered the exact level of accurate detail needed to assist novice and advanced users in conquering the XP/2oo0 install issue on SATA. If your friend really wants XP, I'd suggest getting Win 7 Professional or Ultimate and running Windows XP mode. If you get a boot problem after performing your motherboard swap, this is the very first place to look. I make driver floopy disk, start installing, load the driver ("F6″) and then, when the installation asked me for partition, there was only one (the old one hard drive) there. https://www.raymond.cc/blog/move-windows-xp-hard-drive-or-change-motherboard-without-getting-blue-screen-of-death/
i have 2 sata drives and 1 ide drive.runing windows xpi'm having problems with my ide drive.my system iswindows xp proffessional1 gig memorysata drive 1 160 gigsata drive 2 300 gigide Do those IDE converters to SATA work ? Then i opened xp. Windows Xp Motherboard Info I have two SATA drives as my main drives, and I have two IDE drives (one refuses to operate), so I installed the one IDE drive into my system, and have
Alastair Odyssey Says: January 6th, 2010 at 6:11 am Also - although I could update the MB, I have a hugely expensive Parhelia AGP quad video card that I really don't Unless of course you don't mind getting infected with spyware and virusses often of course. a new hard drive has no data on it - a hard drive that has had it's operating system deleted will not be bootable- if it does have an operating system The Windows XP installation process breifly indicates that, in order to install "third party" or "Raid" drivers, function key "F6" must be immediately pressed and, I understand, that it will only
Since we are going to be adding new hardware to the system make sure your computer is powered off, with the AC power cable disconnected from the system to prevent and Clone Windows Xp To Another Computer Any ideas/thoughts would be most helpful Hi. Depending upon your bios and startup options, if it is like mine you have the option either within the bios, or at startup, which drive to choose as the primary. Since SATA drivers are inherent within the full installation of windows you can use a utility that is provided by the system to setup and configure your new SATA drive.
As mentioned before setting up the SATA driver disk for a VIA chipset is a very different process then setting up for the nVidia chipset. http://superuser.com/questions/961616/windows-xp-new-motherboard-the-os-is-installed-but-the-system-doesnt-boot But despite that, the bios does recognize the drives are there but I can't figure out why XP won't boot. Move Windows Xp Hard Drive To New Computer I looked on Ebay and don't see one for updates. How To Copy Windows Xp From One Computer To Another Report • #2 OtheHill May 14, 2012 at 14:59:55 Get nliteOS from the link below.
Depending on the drive and connection it may either be a flat black connection about 1.5 inches wide, or the standard 4 pin Molex connection used with normal hard drives. 04. this content The first thing you will need to do is put the motherboard CD that came with your mainboard into your system. Note: USB devices are reinstalled on a per-root basis, so it is perfectly normal to see them more than once in any list with Device Manager in this mode. Thank You in advance for your input! :=] -=LRO=- Mike Says: March 15th, 2010 at 11:08 am Hi. Transferring Windows Xp To Another Computer
Installing Windows Two scenarios are possible: You have a floppy drive After setting the BIOS to boot on the CD-ROM or DVD-ROM, insert the Windows installation CD and follow the steps This way you can make sure it does not miss the SATA driver prompt screen when it has finished loading all the drivers. 07. Congratulations you have now installed you SATA hard drive into your system. weblink After replacing the cable, the problem was resolved.
by R. Fix Hdc I have still been unable to recover the lost data, using recovery programs, etc., I think the info is still there, but I'm not going to pay a high price to by rbird / July 22, 2005 11:48 PM PDT In reply to: Mixing SATA and IDE drives in a system?
This step may not be necessary because Windows can usually identify a SATA hard drive after it has been fully installed as mentioned above. My primary was a SATA and 2nd hd bay was an IDE. Then added device line(s) to the config.sys file. Move Hard Drive From One Computer To Another I am going to attempt my own advice shortly.
Since the computer cannot boot into Windows XP, the "Device Manager" cannot be accessed and used to install the SATA HDD driver. After the registry patch on the new install, the administrative tools disk management appeared willing to partition the newly discovered extra space. U may need to reinstall windows after setting this. check over here You may be surprised at how much stuff is faded or ghosted out.
The system shows a normal Windows XP start screen for a second, then it shows the BSOD for a fraction of second, then tries to reboot again. BTW, the hard drives are: 1 WD 320GB Caviar Blue (The main/boot drive), and 1 Hitachi Deskstar 80GB.Any help or advice is appreciated 4 answers Last reply Apr 7, 2014 Best The options will be IDE mode and AHCI mode. The post is based on an excellent thread on the same topic, which everyone who's contemplating a motherboard swap should check out first.
Is the SATA hard drive being detected there ?If the bios is NOT detecting it there....- Check your SATA data cables. Operating Systems ▼ Windows 10 Windows 8 Windows 7 Windows XP See More... This one has PhoenixBios Setup Utility...I do not see that as an option...I don't mean to sound stupid, but I have gone thru everything on this one and don't see AHCI...it Find the SATA hard drive, which should be denoted as "Disk 1″ or similar.
However, instead of getting the WinXP installation screen, It goes through the same process of copying of files as before. Of course there is a 3rd alternative, if your laptop supports it, you can install either Vista or Win7, they both have driver support built into the install program for AHCI